Best Dehumidifier for Mould Australia 2026: 5 Picks by Room and Climate
Drafted with AI assistance and checked against published specifications and certifications. First-hand measurements appear only where stated. How we make content
How this assessment was made. I have not run these dehumidifiers in my own home. Each one is assessed on the manufacturer’s published specifications for the Australian model, including the conditions its litres-per-day rating was measured at, on National Asthma Council Sensitive Choice approvals, and on CHOICE’s published findings about how dehumidifier types behave. Prices, stock and ratings were checked on Amazon Australia on 28 Oct 2026. Mould advice comes from the US EPA, the WHO, the Queensland Government and Asthma Australia. Clean and Native may earn a commission on some links.
The best dehumidifier for mould in most Australian homes is a compressor unit with an adjustable humidistat and a drain hose, set to keep the room below 60% humidity. For bedrooms and living rooms in Queensland and coastal NSW, that is the De’Longhi DEX214F (14 litres a day, about $499 online). For a big or very wet room, the Ausclimate Medium 20L (about $349). For a cold southern room where winter condensation grows the mould, a desiccant unit: the Ausclimate Cool Seasons (about $389). As the US EPA puts it, “The key to mold control is moisture control.” A dehumidifier is how you control it in a room you can close up.
On the Gold Coast and in Brisbane, a wet summer is when wardrobes go musty and black spots appear on bathroom ceilings. As a former Navy Clearance Diver, I’m in the habit of reading the gauge before trusting the gear, and with mould the gauge is a humidity meter. Measure first, then buy the dehumidifier the reading calls for. This guide shows how.
Buy a compressor dehumidifier for warm, humid rooms, a desiccant one for cold rooms, and a mini Peltier unit only for a wardrobe. Set it to about 50% and run it on a drain hose.
| Pick | Best for | Price |
|---|---|---|
| De’Longhi DEX214F | Bedrooms and living rooms to ~27 m² | Currently unavailable on Amazon AUas of 19 Nov 2026, 5:29 pm AEST Details |
| Ausclimate Medium 20L | Large or very damp rooms to 30 m² | $284.00at Amazon AU · as of 19 Nov 2026, 8:29 pm AEST Details |
| Breville Smart Dry Connect | Quieter bedrooms, 20 to 30 m² | $319.20at Amazon AU · as of 19 Nov 2026, 8:29 pm AEST Details |
| Ausclimate Cool Seasons 10L | Cold rooms and southern winters (desiccant) | $388.50at Amazon AU · as of 19 Nov 2026, 8:29 pm AEST Details |
| CLEVAST mini | Wardrobes and cupboards only | $59.49at Amazon AU · as of 19 Nov 2026, 8:29 pm AEST Details |
✓ A dehumidifier is the right tool if
- Indoor humidity sits above 60% for days at a time
- Mould keeps coming back on ceilings, walls or in wardrobes after you clean it
- Clothes, shoes or bedding smell musty after the wet season
- Windows stream with condensation on winter mornings
- You need to dry a room out after a leak or flood
× It won’t solve it if
- Water is still getting in: a leaking roof, shower or pipe, or rising damp
- Mould covers a large area (that is a remediation job)
- You leave windows open while it runs on humid days
- The room is a wardrobe-sized space and you buy a large unit (or the reverse)
Why humidity is the lever that matters
Mould needs moisture, warmth and something to feed on. In a house you can’t remove the food (timber, plasterboard, fabric, dust) and in Queensland you can’t remove the warmth, which leaves moisture. The US EPA advises keeping indoor humidity “below 60 percent (ideally between 30 and 50 percent) relative humidity,” and to “Use air conditioners and/or de-humidifiers when needed.” CHOICE puts the comfortable range for people at 40 to 60%.
It isn’t a niche problem. The World Health Organization’s guidelines on dampness and mould estimate that dampness affects “10 to 50% of indoor environments in Europe, North America, Australia, India and Japan,” and that people in damp or mouldy buildings are at “increased risk of respiratory symptoms, respiratory infections and exacerbation of asthma.” The WHO’s recommendation is prevention: keep buildings from staying damp.
Speed matters too. The EPA says it is important to “dry water-damaged areas and items within 24-48 hours to prevent mold growth.” After a leak or a flooded floor, a dehumidifier running with the doors shut is one of the fastest ways to do that.
Measure before you buy
The EPA notes that a basic humidity meter costs about $10 to $50. Put one in the problem room and read it morning and evening for a week, with the windows as you normally keep them. Many home air quality monitors also show humidity; see the best air quality monitors.
| Reading most of the week | What it means | What to do |
|---|---|---|
| Under 50% | Dry enough for mould not to thrive | No dehumidifier needed. Look for a leak or a cold spot if mould still grows |
| 50 to 60% | Borderline | Ventilate, use exhaust fans, dry clothes outside. Re-check in the wet season |
| Over 60% | Mould-friendly | Dehumidifier in the room, doors closed, set to about 50% |
| Over 60% and it won’t drop | Water is getting in, or the unit is too small | Find the moisture source. Then size up |
Condensation is a reading too. The EPA says “Condensation can be a sign of high humidity,” and streaming windows on cold mornings are the usual sign of the winter mould you see in Melbourne, Hobart and Canberra homes.
Compressor vs desiccant vs Peltier
Compressor (refrigerant) dehumidifiers pull air over a cold coil so water condenses on it, like the back of a fridge. They are the right type for warm, humid rooms, which covers most of Queensland, northern NSW and Sydney’s summers. CHOICE notes that they “don’t work so well in cold air”: in its testing, a refrigerant model “extracted more than four times as much water in hot conditions as it did in cold conditions.”
Desiccant dehumidifiers absorb water into a rotating wheel and heat it to release it. CHOICE says they “can be much more effective than refrigeration models in cold climates” and that “their performance should be largely unaffected by the air temperature.” The trade-offs: CHOICE says desiccant models “rarely exceed a rated extraction rate of 10L per day,” and the heater uses more power (730 W for the Ausclimate below, against 310 W for the De’Longhi). They also warm the room slightly, which is welcome in a cold bedroom and not in a Brisbane summer.
Peltier (thermoelectric) mini units use a small electronic cold plate. They are quiet and cheap, and they remove very little water: CLEVAST rates its mini unit at 295 mL a day at 30°C and 85% humidity, about a fiftieth of the De’Longhi’s rating. That is fine for a wardrobe or a linen cupboard. It won’t change the humidity of a bedroom.
Why litres per day can mislead
CHOICE warns that “Manufacturers might give water removal rates at conditions which make their machines look the best.” Compressor units are usually rated at 30°C and 80% humidity, a hot, steamy room. The Ausclimate desiccant is rated at 20°C and 60%. Those are different tests, so a 10 L desiccant and a 10 L compressor unit are not the same machine. In a cool room, expect a compressor unit to remove far less than its label says; the rating conditions are much closer to a Queensland summer. When you compare models, compare the test conditions as well as the number.
The best dehumidifiers for mould
1. De’Longhi DEX214F: best overall
Best overall14 L/dayat 30°C, 80% RH (De’Longhi)Compressor (R290) | Rooms up to 65 m³ (~27 m²) | 2.1 L tank + continuous drain hose | 310 W | Runs 2 to 30°C | Dust and allergen filters | 2-yr warranty
Check the DEX214F Price on Amazon →The DEX214F is the one I’d buy for a mould-prone bedroom or living room in a warm, humid home. De’Longhi rates it at 14 litres a day at 30°C and 80% humidity, for rooms up to 65 m³, which is about 27 m² at a standard 2.4 m ceiling. It has an adjustable humidistat, so it switches off at the level you set instead of running flat out, a continuous drain hose so you don’t have to empty the 2.1 L tank, a laundry mode for drying clothes inside, and dust and allergen filters. It draws 310 W, runs from 2 to 30°C, and uses R290, a natural refrigerant. De’Longhi says its dehumidifiers are approved under the National Asthma Council’s Sensitive Choice program.
✓ Pros
- Adjustable humidistat and drain hose: set it and leave it
- Compact: about 33 cm wide and 22 cm deep, with a carry handle
- Established brand with a 2-year Australian warranty
× Cons
- Small 2.1 L tank if you don’t use the hose
- Rated room size is modest (~27 m²)
- Like any compressor unit, weak in a cold room
Buy this if…
the mould problem is a bedroom, study or living room in a warm, humid home, and you want one reliable unit that runs on a hose.
2. Ausclimate Medium 20L: best for large or very wet rooms
Large or wet rooms20 L/dayat 30°C, 80% RH (Ausclimate)Compressor | Rooms up to 30 m² (75 m³) | 3.5 to 4 L tank (listings differ) + gravity drain outlet | 42 to 48 dBA | 330 W | Adjustable humidistat, timer | 2-yr warranty or longer (retailers differ)
Check the Ausclimate 20L Price on Amazon →Amazon AU price: $284.00 · as of 19 Nov 2026, 8:29 pm AEST DetailsFor a large rumpus room, a downstairs room against a damp slab, or drying out after a leak, you want more extraction than 14 litres. Ausclimate rates the Medium 20L at 20 litres a day at 30°C and 80% humidity, for rooms up to 30 m², with a 42 to 48 dBA noise rating, a 330 W draw, a timer, an adjustable humidistat and a gravity drain outlet (the hose has to run downhill). Ausclimate is an Australian brand; retailers list a warranty of 2 years or more. It is the best price per litre on this list at about $349. The catch: the listings disagree on the tank size (3.5 or 4 L) and the warranty.
✓ Pros
- 20 L/day rating for about $349
- Rated 42 to 48 dBA
- Gravity drain outlet for a hose
× Cons
- Listings disagree on tank size and warranty
- Heavier (about 15 kg)
Buy this if…
the room is big, very damp, or drying out after water damage, and value matters more than a long track record.
3. Breville Smart Dry Connect: best for quiet bedrooms
Quiet bedrooms<40 dB(A)Breville ratingCompressor | 10 L/day (test conditions not stated) | Rooms 20 to 30 m² | 2.5 L tank + continuous drain hose | 220 W | App control | Sensitive Choice approved | 2-yr warranty
Check the Breville Smart Dry Price on Amazon →Amazon AU price: $319.20 · as of 19 Nov 2026, 8:29 pm AEST DetailsCHOICE notes that “Most dehumidifiers make upwards of 50 decibels (dB) of noise,” enough to disturb sleep. Breville rates the Smart Dry Connect at under 40 dB(A), which makes it the one to put in a bedroom you sleep in. It removes 10 litres a day (Breville doesn’t state the test conditions), suits rooms of 20 to 30 m², draws 220 W, has a 2.5 L tank and a 1 m continuous-drain hose, and connects to the Breville app so you can see the humidity from your phone. It is on the Sensitive Choice list.
✓ Pros
- Rated under 40 dB(A)
- 220 W, the lowest power of the full-size units here
- Drain hose and app included
× Cons
- 10 L/day with no stated test conditions
- Less capacity than the De’Longhi for similar money
- App adds little if you just leave it on a setpoint
Buy this if…
the dehumidifier has to run in the bedroom overnight and noise is the deciding factor.
4. Ausclimate Cool Seasons 10L: best for cold rooms and southern winters
Cold rooms and winter1 to 40°Coperating range (Ausclimate)Desiccant | 10 L/day at 20°C, 60% RH | Up to 50 m² | 3 L tank + 1.2 m drain hose | 38 to 49 dBA | 730 W | Sensitive Choice approved | 2-yr warranty
Check the Cool Seasons Price on Amazon →Amazon AU price: $388.50 · as of 19 Nov 2026, 8:29 pm AEST DetailsIf your mould shows up in winter, on the inside of cold windows and the corners of south-facing rooms, a compressor unit will struggle, because cold air holds less water and its coil can’t pull much out. The Cool Seasons is a desiccant unit rated at 10 litres a day at 20°C and 60% humidity, with an operating range of 1 to 40°C, coverage up to 50 m², a 3 L tank and a 1.2 m drain hose, and 38 to 49 dBA. It is on the Sensitive Choice list. The cost is power: 730 W, more than double the De’Longhi. It also warms the room a little, which suits a Melbourne bedroom in July and not a Brisbane one in February. About $389.
✓ Pros
- Keeps working in cold rooms
- Biggest rating base of the full-size picks
- Quiet on low (38 dBA)
× Cons
- 730 W: the most expensive to run
- Adds heat to the room
- 10 L/day ceiling, typical of desiccants
Buy this if…
you live in Victoria, Tasmania, the ACT or the cooler parts of NSW and the mould problem peaks in winter.
5. CLEVAST mini: wardrobes and cupboards only
Wardrobes only295 mL/dayat 30°C, 85% RH (CLEVAST)Thermoelectric (Peltier) | 850 mL tank, auto-off when full | 0.55 kWh a day | 24 dB claimed | No humidistat listed
Check the CLEVAST Price on Amazon →Amazon AU price: $59.49 · as of 19 Nov 2026, 8:29 pm AEST DetailsSome mould problems are small: a wardrobe against an outside wall, a linen cupboard, a shoe rack. A mini Peltier unit is the right size for those. CLEVAST rates this one at 295 mL a day at 30°C and 85% humidity, with an 850 mL tank that switches the unit off when full, and 0.55 kWh a day of power use. In a closed wardrobe, that rate is in proportion to the space. Don’t buy one for a bedroom: at that extraction rate it can’t keep up. It costs about $70 online.
✓ Pros
- About $70 and very quiet
- Right-sized for a closed wardrobe
- Switches off when the tank is full
× Cons
- 295 mL a day: useless for a whole room
- No humidistat listed
- Tank needs emptying by hand
Buy this if…
the mould is confined to a wardrobe or cupboard and the rest of the house reads under 60%.
Comparison table
| Spec | DEX214F | Ausclimate 20L | Breville Smart Dry | Cool Seasons | CLEVAST |
|---|---|---|---|---|---|
| Type | Compressor | Compressor | Compressor | Desiccant | Peltier |
| Rated extraction | 14 L/day | 20 L/day | 10 L/day | 10 L/day | 0.3 L/day |
| Rating conditions | 30°C, 80% | 30°C, 80% | Not stated | 20°C, 60% | 30°C, 85% |
| Room size (maker) | 65 m³ (~27 m²) | 30 m² | 20 to 30 m² | 50 m² | Wardrobe |
| Power | 310 W | 330 W | 220 W | 730 W | 0.55 kWh/day |
| Noise (maker) | 40 (unit not stated) | 42 to 48 dBA | <40 dB(A) | 38 to 49 dBA | 24 dB |
| Tank / drain hose | 2.1 L / yes | 3.5 to 4 L / gravity outlet | 2.5 L / yes | 3 L / yes | 0.85 L / no |
| Price (28 Oct 2026) | ~$499 | ~$349 | ~$369 | ~$389 | ~$70 |
Check all seven rooms, not just this one
38 checks, 29 free, ranked by impact. Sent as a 32-page PDF.
We'll email you the audit and a short series of practical guides. Unsubscribe in one click, any time. Privacy.
Sent. Taking you to your download...
Running costs
Running cost is power draw times hours times your tariff. The table uses 35c per kWh (swap in the rate on your bill) and 8 hours a day at full power. A unit on a humidistat switches its compressor off once the room reaches the setpoint, so real costs are usually lower.
| Unit | Power | kWh in 8 hours | Cost a day | Cost a month (30 days) |
|---|---|---|---|---|
| De’Longhi DEX214F | 310 W | 2.48 | ~$0.87 | ~$26 |
| Ausclimate Medium 20L | 330 W | 2.64 | ~$0.92 | ~$28 |
| Breville Smart Dry | 220 W | 1.76 | ~$0.62 | ~$18 |
| Ausclimate Cool Seasons (desiccant) | 730 W | 5.84 | ~$2.04 | ~$61 |
| CLEVAST mini (24 hours) | 0.55 kWh/day | 0.55 a day | ~$0.19 | ~$6 |
Per litre removed, at each maker’s own rating conditions, the Ausclimate 20L uses about 0.4 kWh, the De’Longhi about 0.5 kWh, the desiccant about 1.75 kWh and the CLEVAST about 1.9 kWh. The conditions differ, so treat that as rough, but the pattern is real: compressor units are the cheapest way to move water in a warm room, and a mini Peltier unit is an expensive way to move very little of it.
How to set it up for mould
Close the room. A dehumidifier dries the air in the space it’s in. With doors and windows open on a humid day, it is trying to dry the street.
Set about 50%. That keeps you under the EPA’s 60% line with margin and inside CHOICE’s 40 to 60% comfort range. Some units, including mechanical humidistats like the DEX214F’s, use a dial with set steps rather than exact percentages; pick the setting nearest 50%.
Use the drain hose. CHOICE notes a continuous drain is useful “if the dehumidifier will be run for long periods in the same location.” A unit that stops every time the tank fills isn’t controlling anything overnight.
Place it near the problem, not against it. Put it in the open part of the room near the damp wall or wardrobe, with the clearance around the intake and outlet that the manual specifies. Clean its filter as the manual says, and empty and rinse the tank if you don’t use a hose.
After a leak or flood, run it on its highest setting with the room closed to get materials dry within the EPA’s 24 to 48 hours, then drop it back to the setpoint.
When a dehumidifier isn’t enough
Water still getting in. A leaking roof, shower or pipe, a blocked gutter or rising damp will out-supply any portable unit. If the room won’t drop below 60% with a correctly sized unit running on a closed room, look for the source. The EPA’s first instruction is to “Fix plumbing leaks and other water problems as soon as possible.”
Mould already on the surfaces. Drying the air doesn’t remove it. The Queensland Government suggests cleaning small areas with 3 parts vinegar to 2 parts water, or 70% methylated spirits and 30% water, and warns: “Don’t dry brush the area with a broom or brush, as this can spread mould.” The EPA says bleach “is not recommended as a routine practice during mold cleanup.” Asthma Australia advises a disposable P2 mask, gloves and goggles. The EPA says most people can handle an area under about 10 square feet (about 1 m²); bigger than that, get help.
Spores in the air. A dehumidifier’s filter is a dust screen, not a HEPA filter. If someone in the house has asthma or allergies, add a HEPA air purifier in the bedroom; see the best air purifiers for mould and, for which to buy first, dehumidifier vs air purifier for mould.
Ventilation. The Queensland Government advises letting air circulate, especially in the bathroom, ventilating when cooking or showering, venting the clothes dryer outside, and not running an evaporative cooler with water when humidity is over 65%. Exhaust fans are cheaper to run than any dehumidifier.
What we left out
The generic “140 m², 10L” unit this page used to recommend: the brand isn’t clear from the listing, and a 140 m² claim for a 10 L/day unit isn’t credible next to De’Longhi’s and Ausclimate’s room ratings. Two-in-one dehumidifier and purifier units, such as De’Longhi’s DDSX220WF: De’Longhi lists an EPA 12 filter (not HEPA) tested at 80 m³/h of airflow, a fraction of a bedroom purifier’s, at about $617. A separate dehumidifier and HEPA purifier do both jobs better. Mini Peltier units for bedrooms: they can’t remove enough water. Moisture-absorber tubs: fine for a cupboard, no help in a room.
Which should you buy?
Warm, humid bedroom or living room (most of Queensland and coastal NSW): De’Longhi DEX214F. A large or very wet room, or drying out after water damage: Ausclimate Medium 20L. It has to run beside the bed: Breville Smart Dry Connect. Mould that peaks in winter, in a cold room: Ausclimate Cool Seasons desiccant. One musty wardrobe: CLEVAST mini. Asthma or allergies in the house: add a HEPA purifier; see the best air purifiers for asthma.
Final verdict
Buy the hygrometer first. If the room sits above 60%, a compressor dehumidifier on a drain hose, set to about 50% with the door shut, is the most effective thing you can buy for mould. For most warm Australian homes, that is the De’Longhi DEX214F; for big or wet rooms, the Ausclimate Medium 20L; for cold winter rooms, the Ausclimate Cool Seasons desiccant. Fix any leak first, clean what’s already there, and the dehumidifier keeps it from coming back.
Prices change. Check Amazon AU before buying.
Frequently asked questions
What humidity stops mould growing?
The US EPA advises keeping indoor humidity below 60%, ideally between 30% and 50%. Setting a dehumidifier to about 50% keeps you under that line with a margin and inside CHOICE’s 40 to 60% comfort range.
What is the best dehumidifier for mould in Australia?
For most warm, humid homes, a compressor unit with a humidistat and drain hose. The De’Longhi DEX214F (14 L a day, about $499) suits bedrooms and living rooms; the Ausclimate Medium 20L (about $349) suits large or very damp rooms.
Is a desiccant or compressor dehumidifier better for mould?
It depends on the temperature. Compressor units are better in warm, humid rooms. CHOICE found a refrigerant model removed more than four times as much water in hot conditions as in cold, and says desiccant models can be much more effective in cold climates.
Does a dehumidifier kill mould?
No. It removes the moisture mould needs, so cleaned areas stay clean. Clean existing small patches first (the Queensland Government suggests 3 parts vinegar to 2 parts water) and fix any leak.
Are small Peltier dehumidifiers any good for mould?
Only in a wardrobe or cupboard. The CLEVAST mini, for example, is rated at 295 mL a day at 30 degrees and 85% humidity. That can’t lower the humidity of a bedroom.
Should I run a dehumidifier all the time?
Run it on its humidistat, set to about 50%, with the room closed and a drain hose fitted. It then runs only when humidity rises above the setpoint.
How much does a dehumidifier cost to run?
At 35c per kWh, a 310 W compressor unit like the De’Longhi DEX214F costs about 87c for 8 hours at full power, about $26 a month. A 730 W desiccant unit costs about $2 for the same 8 hours.
Do I need an air purifier as well as a dehumidifier?
Only if someone in the house has asthma or allergies, or while you are cleaning mould. A dehumidifier’s filter is a dust screen, not a HEPA filter. A HEPA purifier in the bedroom catches the spores still in the air.
- US EPA: A Brief Guide to Mold, Moisture and Your Home
- WHO Guidelines for Indoor Air Quality: Dampness and Mould (2009), summary
- CHOICE: how to buy a dehumidifier (refrigerant vs desiccant, noise, capacity)
- Queensland Government: mould and damp
- Asthma Australia: mould health hazard warning after floods (updated 19 Feb 2025)
- De’Longhi DEX214F specifications (Appliances Online: 14 L at 30°C, 80% RH; R290)
- De’Longhi DEX214F specifications and dimensions (Home Clearance)
- De’Longhi Australia: dehumidifiers (Sensitive Choice statement)
- Ausclimate Medium 20L ACD220 specifications (Appliances Online)
- Ausclimate Medium 20L specifications (Hydroexperts: drain outlet, 330 W)
- Breville the Smart Dry LAD208 specifications (Betta)
- Sensitive Choice: approved Breville dehumidifiers (BAD208)
- Ausclimate Cool Seasons Premium AU-1910DD specifications (Appliances Online)
- Sensitive Choice: approved Ausclimate dehumidifiers (AU-1910DD)
- Sensitive Choice: what the blue butterfly means
- CLEVAST small dehumidifier: Amazon AU listing (295 mL a day at 30°C, 85% RH)
- De’Longhi Australia: Tasciugo AriaDry Pure DDSX220WF (EPA 12 filter, 80 m³/h test)
The 7-Room Home Audit
Air is where most homes have their biggest free fix. The audit walks every room: 38 checks across air, water and EMF, ranked by impact against Australian guidelines.
- The rangehood habit that cuts gas cooking fumes
- Two-minute tests for exhaust fans, mould and stale bedrooms
- When a purifier helps, and the bedroom one I own
We'll email you the audit and a short series of practical guides. Unsubscribe in one click, any time. Privacy.
Sent. Taking you to your download...
