Closed grey electricity meter box on the brick side wall of a suburban Australian house

Smart Meter EMF Opt Out in Every Australian State 2026

25 min read

Drafted with AI assistance and checked against published specifications and certifications. First-hand measurements appear only where stated. How we make content

Affiliate disclosure: Clean and Native earns a commission if you purchase through links on this page, at no extra cost to you. We only recommend products we have researched and believe meet the standards described here. How we test.

Australian smart meters transmit RF pulses at 900 MHz with peak power densities between 0.2 and 8.0 µW/cm² at one metre — well within ARPANSA’s limit of about 450 µW/cm² at 900 MHz but substantially above the Building Biology SBM-2015 sleeping-area guideline of less than 0.1 µW/m². No Australian state gives you a right to refuse a smart meter, but in most of the country you can ask your retailer to have its communications switched off. The rules differ by state, and Victoria is the exception.

Quick Verdict – Clean & Native
900 MHz
AU Smart Meter Freq
0.2 to 8
µW/cm² at 1 m peak
100 to 1000×
Peak vs Time-Average
2030
National rollout target
State Opt-Out Path Verdict
NSW, ACT, QLD, SA, TASCan’t refuse the meter; ask your retailer to switch its communications off (manual reads)Available, usually with charges
VictoriaRegulations don’t allow communications to be disabledNot available
Western AustraliaOutside the national rules; ask Western PowerAsk the network
Northern TerritoryOutside the national rules; ask Power and WaterAsk the network

No Australian state gives you a right to refuse a smart meter. In NSW, the ACT, Queensland, South Australia and Tasmania you can ask your retailer to have its communications switched off; Victoria’s rules don’t allow it. Before you begin the opt-out process, measure your actual exposure first: most bedrooms already exceed Building Biology sleeping-area RF guidelines from Wi-Fi routers and phones, which contribute far more RF than the meter on your exterior wall. The TriField TF2 is the most cost-effective way to identify what you are actually exposed to — and whether the smart meter is even your primary source.

Key catches

  • In NSW, the ACT, Queensland, SA and Tasmania, requests go to your retailer (AGL, Origin, EnergyAustralia and so on), not your distributor
  • Expect charges for manual meter reading once communications are off; your retailer must tell you what they are first
  • A “non-transmitting” smart meter still contains RF hardware — its radio module is disabled, not removed
  • Shielding the meter without first removing internal bedroom RF sources (Wi-Fi router, phone, DECT phone) can increase total exposure via reflection
See TriField TF2 Price →Amazon AU price: $299.00 · as of 19 Nov 2026, 11:43 pm AEST Details EMF Measurement Guide →

What Your Smart Meter Actually Transmits — and Why Peak Matters More Than Average

Every Australian AMI (Advanced Metering Infrastructure) smart meter operates on the 900 MHz band regulated by ACMA. According to ARPANSA Radiation Protection Standard RPS S-1, the general public RF exposure limit at 900 MHz is approximately 450 µW/cm² (4.5 W/m²). Smart meters sit well below that — but the number ARPANSA uses is a time-averaged figure, and that is where the problem starts for anyone sleeping one wall away from the meter box.

Smart meters do not broadcast continuously. They transmit usage data in short RF bursts — typically lasting 2-20 milliseconds — at intervals ranging from every 15 seconds to every 4 hours, depending on the distributor’s network configuration. Energex meters in south-east Queensland and Ausgrid meters in Sydney use a 900 MHz mesh network (Zigbee or proprietary protocols) that relays data between neighbouring meters before reaching a collector node.

The critical distinction is between time-averaged and peak exposure. ARPANSA’s compliance framework uses a 6-minute time average. During those 6 minutes, a meter might transmit for a cumulative total of 0.5 seconds. The time-averaged reading looks trivially low — often 0.001 µW/cm². But the peak power density during each burst can measure 0.2 to 8.0 µW/cm² at one metre from the meter, and substantially higher if the meter is a mesh relay handling data from multiple neighbouring properties.

For context, here is how smart meter RF compares to other common household sources:

RF Source Frequency Peak at 1 m Duty Cycle Bedroom Impact
Smart meter (900 MHz)900 MHz0.2 to 8.0 µW/cm²<1% typicalWall attenuates 10 to 20 dB; lower indoors
Wi-Fi router (2.4 GHz)2.4 / 5 GHzAbout 0.3 to 0.4 µW/cm² right beside the router (my TF2 reading)10 to 90% (always pinging)Typically highest bedroom source
Mobile phone (active call)700 to 2600 MHzHighest at the handset; falls fast with distanceNear-continuous during callAgainst head = max personal exposure
DECT cordless phone1.9 GHzVaries by modelContinuous (even idle)Constant emitter — remove from bedroom
Building Biology SBM-2015 limitAny<0.00001 µW/cm²N/APrecautionary sleeping guideline

The table makes the priority clear. Your Wi-Fi router and any phone left on the bedside table almost certainly contribute more RF to your sleeping environment than the smart meter on the exterior wall. That does not mean the smart meter is irrelevant — if your bedroom wall shares the exterior where the meter box is mounted, peak burst readings can still exceed Building Biology guidelines indoors. But before you spend time and money on an opt-out process, measure your actual exposure. The sequence matters: measure first, then address sources in order of contribution.

Key takeaway: According to ARPANSA RPS S-1, smart meter emissions comply with Australia’s thermal safety limits. However, peak burst readings are 100-1,000 times higher than time-averaged figures. Always use peak-hold mode on your EMF meter when measuring smart meter RF — a 6-minute average reading will dramatically understate what you are exposed to during each transmission burst.

Why You Must Measure Before You Opt Out — the Correct Reduction Sequence

I am a former Navy Clearance Diver. In diving, we follow a strict sequence: assess the hazard, identify the source, mitigate the highest-risk item first. EMF reduction works the same way. If you skip measurement and go straight to an opt-out application, you might spend months navigating your retailer’s process while your Wi-Fi router keeps transmitting beside your bed every night.

The correct sequence for reducing bedroom RF exposure is:

  1. Measure — take peak-hold RF readings at your bed position, at the smart meter wall, at the router, and at any other suspected source. Use a meter like the TriField TF2 or the Safe and Sound Pro II for dedicated RF measurement.
  2. Remove or disable internal sources — put your phone in airplane mode at night (free), put a mechanical timer on your Wi-Fi router ($20), remove DECT cordless phones from the bedroom entirely.
  3. Re-measure — confirm which sources remain. If the smart meter is now the dominant residual source, proceed to opt-out or shielding.
  4. Opt out or shield — apply for non-transmitting mode, analog retention, or (only after internal sources are gone) shield the meter wall externally.

The shielding trap is real. If you install a Faraday canopy or RF-shielding paint on an interior wall while your Wi-Fi router is still broadcasting inside the room, the shielding reflects that internal RF back toward you, increasing your exposure. Shielding is only appropriate once you have confirmed all significant internal sources are eliminated. This is documented in the Building Biology SBM-2015 guidelines for sleeping areas: shield external residual RF only, never internal sources.

After addressing internal sources, many households find the smart meter was never their main source. For the remainder — particularly bedrooms where the bed headboard shares the exterior meter-box wall — the opt-out process is worth pursuing. Here is exactly how to do it in every Australian state.

Key takeaway: Putting your phone in airplane mode and scheduling your Wi-Fi router on a $20 mechanical timer delivers more RF reduction in most bedrooms than a smart meter opt-out. Do the free and cheap actions first. Then measure what remains.

Smart Meter Opt-Out in Australia: What the Rules Actually Allow (2026)

Two sets of rules decide this. NSW, the ACT, Queensland, South Australia and Tasmania follow the National Energy Retail Law and the National Electricity Rules. Victoria, Western Australia and the Northern Territory run their own systems. In the national-rules states your meter is your retailer’s responsibility: the retailer appoints a metering coordinator, which owns and manages the meter. Your distributor (Ausgrid, Energex, SA Power Networks and so on) is not the place to send an opt-out request.

NSW, ACT, Queensland, South Australia and Tasmania

  • You can’t refuse the meter. The AEMC’s 2024 rule to accelerate the rollout aims to put a smart meter in every home by 2030, and the Queensland Government’s guidance is plain: customers can no longer refuse or opt out of a new smart meter arranged by their retailer.
  • You can ask for its communications to be switched off. Since 1 July 2019 the national rules have let a metering coordinator deactivate the remote communications on an installed smart meter at the customer’s request. The meter then works as a manually read meter (a type 4A meter in the rules). You can also ask for a new meter to be installed with communications switched off. Ask your retailer, in writing.
  • It is not automatic, and it is not free. The metering coordinator decides whether to accept the request, and your retailer must first tell you the upfront and ongoing charges, such as manual meter reading. Without remote reads you may get estimated bills, and some tariffs may not be available to you.
  • If it goes wrong: complain to your retailer first, then to your state or territory energy ombudsman, for example EWON in NSW, EWOQ in Queensland or EWOSA in South Australia.

Victoria

Victoria rolled out smart meters to almost every home between 2009 and 2013 under a state government mandate run by the distributors (CitiPower, Powercor, Jemena, AusNet Services and United Energy). Victoria has not adopted the National Energy Retail Law, so the 2019 national rule above does not apply there, and a 2025 petition to the Victorian Legislative Council notes that Victorian regulations do not allow a smart meter’s communications to be disabled. You can still put your concern to your distributor in writing; if you are unhappy with the response, the Energy and Water Ombudsman Victoria (EWOV) takes complaints.

Western Australia and the Northern Territory

WA (network operator Western Power; retailers Synergy and Horizon Power) and the NT (Power and Water Corporation) sit outside the national rules. Neither publishes a general opt-out, so ask the network operator directly whether a meter’s communications can be switched off and what manual reading would cost, and get the answer in writing.

Rules checked 11 November 2026 against the AEMC, the AER, the Queensland Government and the Parliament of Victoria. Charges and processes vary by retailer.

Key takeaway: In NSW, the ACT, Queensland, South Australia and Tasmania you can’t refuse a smart meter, but you can ask your retailer to have its communications switched off, usually with manual-reading charges. Victoria’s rules don’t allow that. Wherever you live, deal with the RF sources inside your bedroom first.

How to Write an Effective Opt-Out Request Letter

Your opt-out request needs to be in writing — not a phone call. Written requests create a paper trail and start your retailer’s formal complaints process, which the national rules require. Here is what to include:

  1. Your NMI (National Metering Identifier) — found on your electricity bill. This identifies your specific meter, not your account.
  2. Specific request — state clearly that you want the meter’s remote communications switched off. Be specific. “I request that the wireless transmission function of smart meter NMI [number] be permanently disabled” is better than “I have concerns about smart meters.”
  3. Health grounds — reference the proximity of your sleeping area to the meter and cite the Building Biology SBM-2015 precautionary guidelines for sleeping areas (<0.1 µW/m² RF). You do not need a medical certificate, but one supporting your concerns strengthens the request.
  4. ARPANSA reference — note that ARPANSA Radiation Protection Standard RPS S-1 is a thermal safety standard, not a precautionary health guideline, and that you are applying a precautionary approach as recommended by the Building Biology Institute.
  5. Ombudsman escalation statement — state that you will escalate to the relevant Energy and Water Ombudsman if a satisfactory resolution is not reached within 20 business days.

Send via email and registered post. Keep copies of everything. If your retailer acknowledges receipt but delays action, follow up at 10 business days and reference your escalation pathway to the energy ombudsman.

Key takeaway: Always put your opt-out request in writing. Include your NMI, a specific request (switch the remote communications off), and a statement that you will escalate to the Energy and Water Ombudsman if unresolved. Written requests trigger formal complaint-handling obligations that phone calls do not.
Free audit

Check all seven rooms, not just this one

38 checks, 29 free, ranked by impact. Sent as a 32-page PDF.

We'll email you the audit and a short series of practical guides. Unsubscribe in one click, any time. Privacy.

Sent. Taking you to your download...

What to Do While You Wait — Immediate RF Reduction Steps

The opt-out process can take weeks to months. While you wait, these actions deliver measurable RF reduction in your sleeping environment tonight — most of them for free.

Step 1: Phone in airplane mode. Free. Your phone on the bedside table broadcasts at 700-2600 MHz and is almost certainly your highest personal RF source during sleep. Airplane mode eliminates it entirely. If you need an alarm, airplane mode still allows the alarm function.

Step 2: Router on a timer. A HPM 24 Hour Analog Timer costs approximately $20 online. Set it to cut power to your router from 10 PM to 6 AM. Your Wi-Fi router broadcasts beacon frames every 100 milliseconds — even when no device is connected. Switching it off during sleep removes the single highest-duty-cycle RF source in most Australian homes.

Step 3: Remove DECT cordless phones. DECT phones transmit at 1.9 GHz continuously, even when not in use. The base station is a constant emitter. If you have one in or near your bedroom, unplug the base station at night or replace it with a corded phone.

Step 4: Move your bed. Free. If your bed headboard is against the wall that has the smart meter on the other side, move the bed to an interior wall. RF power density decreases with the square of distance — doubling your distance from the meter cuts exposure by 75%. An Australian brick veneer exterior wall provides approximately 10-20 dB of RF attenuation at 900 MHz, but moving the bed further from the wall provides additional reduction without any cost.

Step 5: Measure, then consider shielding. Only after steps 1-4 should you consider physical shielding. If the smart meter is confirmed as the dominant remaining source (via measurement with a TriField TF2 or Safe and Sound Pro II), you can apply aluminium foil tape to the interior of the wall behind the meter, or use EMF shielding paint on that wall section. Shielding on the exterior or meter box itself is not recommended — it can interfere with the mesh network and may prompt your metering provider to replace the meter.

For a comprehensive walkthrough of the entire measurement and reduction process, see our complete guide to EMF in your Australian home.

Key takeaway: The three highest-impact bedroom RF reduction actions — phone in airplane mode (free), router on a $20 mechanical timer, and removing DECT phones — typically deliver more RF reduction than a smart meter opt-out. Do these first. Then measure what remains.

Non-Transmitting Smart Meters vs Analog Meters — Which Is Better?

Under the national rules, the option open to you is a smart meter with its communications switched off. A new analog meter is no longer an option: replacement meters must be smart meters, and the remaining old meters are due to be replaced by 2030. Here is how the two compare.

Non-transmitting smart meter: The RF radio module is disabled via firmware or physical disconnection. The meter retains its digital display, internal logging, and interval data recording — it just stops transmitting wirelessly. A meter reader visits periodically to download data via optical port or handheld device. RF emissions drop to effectively zero from the meter itself. However, the meter still contains RF hardware, and in some configurations, it may still receive (listen for) network signals without transmitting. If you are concerned about the receiving function, ask your retailer to confirm whether the radio is fully disabled in both transmit and receive modes.

Analog accumulation meter: A traditional electromechanical meter with a spinning disc. Zero RF emissions, zero digital components, zero wireless capability. It measures cumulative energy consumption only — no interval data, no time-of-use billing, no remote reading. This is the most complete elimination of meter-related RF. The trade-off is that you lose access to time-of-use tariffs (which can save money if you shift usage to off-peak periods) and detailed consumption data through distributor portals.

What to ask for: if you still have an old analog meter, it will be replaced by 2030; when your retailer schedules it, ask for the new meter to be installed with communications switched off. If you already have a smart meter, ask for its communications to be deactivated.

Key takeaway: Switching the communications off stops the meter’s own RF. In the national-rules states, ask your retailer; expect manual-reading charges. Analog meters are being phased out everywhere by 2030.

Demand Switches, Shielding, and the Smart Meter — Reducing What Remains

Even after addressing RF sources, your bedroom environment may still contain elevated AC electric fields from the house wiring itself. These are not related to the smart meter, but they are relevant to anyone taking a systematic approach to reducing electromagnetic exposure during sleep.

Demand switch: A licensed electrician installs a demand switch on your bedroom circuit for approximately $100-150. When no loads are drawing current (all lights off, nothing plugged in), the demand switch automatically cuts voltage to the circuit, eliminating AC electric fields from the wiring in your bedroom walls. According to Building Biology SBM-2015, AC electric fields in sleeping areas should be below 1 V/m — a demand switch achieves this by removing the field source entirely. This is the single most cost-effective intervention for AC electric field reduction and has nothing to do with your smart meter — but if you are already optimising your sleeping environment, it completes the picture.

Smart meter shielding (exterior wall only): If measurement confirms the smart meter as a significant residual RF source after internal sources are eliminated, you can apply shielding to the interior face of the wall behind the meter. Use EMF shielding paint (graphite-based, grounded to the building’s earth system) or multiple layers of aluminium foil tape behind the plasterboard. Both can achieve 20-40 dB of RF attenuation when properly grounded. Do not shield the meter box itself from the outside — this interferes with the mesh network and may prompt your metering provider to investigate or replace the meter.

For a complete step-by-step guide to bedroom EMF measurement and reduction, including demand switches, router placement, and shielding techniques, read our complete EMF guide for Australian homes.

Key takeaway: A demand switch ($100-150, installed by a licensed electrician) eliminates AC electric fields from bedroom wiring during sleep. Combined with a router timer ($20) and phone airplane mode (free), these three interventions address RF, AC magnetic, and AC electric fields — a complete sleeping-area solution regardless of smart meter status.

The ARPANSA Position vs Building Biology — Understanding the Gap

ARPANSA’s Radiation Protection Standard RPS S-1 sets Australia’s general public RF exposure limit at approximately 450 µW/cm² at 900 MHz (derived from ICNIRP 2020 guidelines). ARPANSA’s published position is that smart meter emissions are well below this limit, and that is accurate: smart meter emissions are trivially small compared to ARPANSA’s thermal safety limit.

The Building Biology Institute’s SBM-2015 guidelines operate on a fundamentally different basis. They are precautionary practitioner guidelines for sleeping areas, not regulatory safety limits. The SBM-2015 RF guideline for sleeping areas is less than 0.1 µW/m² (approximately 0.00001 µW/cm²) — roughly 45 million times more conservative than ARPANSA’s limit at 900 MHz.

Neither standard is “wrong.” They answer different questions. ARPANSA’s limit answers: “At what level does RF cause measurable tissue heating in controlled conditions?” Building Biology’s guideline answers: “What RF level do we observe to be associated with undisturbed sleep in practitioner field experience?” These are not competing answers to the same question — they are answers to entirely different questions.

When you write to your retailer, reference both. ARPANSA compliance demonstrates the meter is legal. Building Biology guidelines demonstrate that precautionary action is not unreasonable. This framing prevents the retailer from dismissing your request as based on “debunked science” while making clear you are aware of the regulatory context.

For detailed guidance on how to interpret ARPANSA’s standards and Building Biology guidelines when measuring your own home, see our EMF measurement guide for Australian homes.

Key takeaway: ARPANSA’s limit (450 µW/cm² at 900 MHz) is a thermal safety standard. Building Biology SBM-2015’s sleeping guideline (<0.00001 µW/cm²) is a precautionary practitioner guideline. Smart meters comply with ARPANSA but can exceed Building Biology thresholds at close range. Reference both in your opt-out request.

Last reviewed: November 2026 – Clean and Native

Final Verdict: Start With Measurement: the TriField TF2 Is the Only Meter You Need.

Measures AC magnetic, AC electric, and RF in one device. Without real readings, every EMF decision is a guess — including whether your smart meter is even your biggest source.

For every other “EMF protection” product, from bed canopies to shungite, the best EMF protection in Australia guide sorts what measurably works from what does not.

Frequently Asked Questions

Can I opt out of a smart meter in Australia?

Not entirely. In NSW, the ACT, Queensland, South Australia and Tasmania you cannot refuse a smart meter, but you can ask your retailer to have its remote communications switched off, which makes it a manually read meter and usually carries charges. Victorian regulations do not allow communications to be disabled. In WA and the NT, ask the network operator.

How much RF does an Australian smart meter emit?

Australian smart meters transmit at 900 MHz with peak power densities of 0.2 to 8.0 µW/cm² at one metre. The duty cycle is typically less than 1%, meaning they transmit for less than 1% of any given time period. Peak readings during bursts can be 100 to 1,000 times higher than the time-averaged figure.

Does a smart meter emit more RF than a Wi-Fi router?

Usually not, averaged over a night. A Wi-Fi router transmits all the time; next to my own modem-router my TriField TF2 read 3.058 to 4.380 mW/m² (about 0.3 to 0.4 µW/cm²). A smart meter’s bursts can be stronger at one metre, but they last milliseconds and its duty cycle is below 1%. Your router is almost always the higher-priority target.

What is the difference between a non-transmitting smart meter and an analog meter?

A non-transmitting smart meter has its wireless radio disabled but retains digital metering and interval data capabilities. An analog meter is a traditional electromechanical device with zero wireless hardware. Both eliminate RF emissions from the meter. Non-transmitting mode preserves time-of-use tariff access; analog does not.

Who do I contact to opt out — my energy retailer or my distributor?

Your retailer, in NSW, the ACT, Queensland, South Australia and Tasmania: under the national rules the retailer is responsible for your meter through its metering coordinator. In Victoria contact your distributor, in WA Western Power, and in the NT Power and Water.

How much does smart meter opt-out cost in Australia?

There is no national fee. Under the national rules your retailer must tell you the upfront and ongoing charges before communications are switched off, typically for manual meter reading, and you may receive estimated bills. Ask for the figures in writing.

Can I shield my smart meter instead of opting out?

You can shield the interior wall behind the meter using EMF shielding paint or aluminium foil tape, which provides 20-40 dB of RF attenuation when grounded. Do not shield the meter box from the outside — this interferes with the mesh network and may prompt your metering provider to replace the meter. Always remove internal RF sources (Wi-Fi router, phones) before shielding any external source.

What is the best EMF meter for measuring smart meter emissions in Australia?

The TriField TF2 measures RF, AC magnetic, and AC electric fields in one device and covers the 900 MHz band used by Australian smart meters. For dedicated RF-only measurement with higher sensitivity, the Safe and Sound Pro II provides audio feedback and peak-hold readings. Always use peak-hold mode — time-averaged readings dramatically understate smart meter burst emissions.

Does ARPANSA say smart meters are safe?

ARPANSA’s position is that smart meter emissions are well below the limits in its standard, RPS S-1. However, ARPANSA’s limits are thermal safety standards based on ICNIRP 2020 guidelines — they protect against tissue heating, not long-term low-level exposure. Building Biology SBM-2015 precautionary guidelines for sleeping areas are approximately 45 million times more conservative than ARPANSA’s limits.

What is the fastest way to reduce bedroom EMF exposure tonight?

Put your phone in airplane mode (free, immediate), plug your Wi-Fi router into a mechanical timer set to cut power during sleep hours ($20), and remove any DECT cordless phone base stations from the bedroom (free). These three actions typically reduce bedroom RF more than a smart meter opt-out.

Jayce Love, former Royal Australian Navy Clearance Diver and Clean and Native founder
Written by Jayce Love

Former Royal Australian Navy Clearance Diver and TAG-E counter-terrorism operator. Founded Clean and Native to apply the same rigorous thinking to the home environment.

Full biography →
Free · 32-page PDF

The 7-Room Home Audit

Distance and off-time do most of the work, and they are free. The audit maps every room: 38 checks across EMF, air and water, ranked by impact.

  • Our own TF2 readings from router to pillow
  • What to check behind the bedhead wall
  • ARPANSA limits and precautionary bands, side by side

We'll email you the audit and a short series of practical guides. Unsubscribe in one click, any time. Privacy.

Sent. Taking you to your download...

Similar Posts