HPM analogue outlet timer connected to Wi-Fi router on timber desk, Australian home office

Router Timer EMF Reduction Australia 2026

28 min read

Drafted with AI assistance and checked against published specifications and certifications. First-hand measurements appear only where stated. How we make content

Affiliate disclosure: Clean & Native may earn a commission from links on this page at no extra cost to you. We only recommend products we have tested or thoroughly evaluated. All opinions are our own. Full disclosure.

Putting your Wi-Fi router on a mechanical timer is the highest-return, lowest-cost EMF intervention available to any Australian household. My TriField TF2 read 3.058 mW/m² at close range to my router and 0.032 mW/m² on the living room couch. A timer that cuts the router’s power overnight takes its RF output to zero while you sleep, removing the single largest continuous RF source in most homes. Mine switches the router off at 9pm and back on at 6am.

Testing note: I have not personally tested the Jackson mechanical timer, the JRS Eco 100 router, or the Safe and Sound Pro II meter discussed here; my assessment of those products is based on published manufacturer specifications and independent certification, not first-hand measurement. The only product I measure first-hand in this article is the TriField TF2, which I own and used for every reading reported below.
Quick Verdict – Clean & Native
$15
Timer Cost (Bunnings)
100%
RF Reduction (Off = Zero)
95×
Distance Reduction (1m vs Bed)
8 hrs
Nightly Off-Time
Intervention
What It Does
Cost
Measured Effect
Verdict
Recommendation
Mechanical timer on router
$15 – RF drops to 0 mW/m² nightly
Do this first
Move router away from bedroom
Free – 95× reduction at distance
Do this second
EMF shielding canopy / paint
$300-$1,500+ – can INCREASE exposure if source is inside
Measure first, shield last

A $15 mechanical timer on your router eliminates 100% of its RF output during sleep – the simplest, cheapest, and most effective EMF reduction available. Distance handles the rest: my couch reading was about 95 times lower than the reading at the router. Before spending $300+ on shielding, measure with a TriField TF2 and follow the sequence: remove sources, increase distance, then – and only then – consider shielding external residual.

Key catches

  • Smart timers (Wi-Fi connected) defeat the purpose – use a mechanical timer only
  • A timer does nothing for electric fields from house wiring: my timber bedhead read 50 to 105 V/m, a separate problem with a separate fix
  • ARPANSA’s limit of 10,000 mW/m² and the building biology ‘no anomaly’ level of 0.0001 mW/m² are 100 million times apart: neither tells you what to do, your own meter readings do
  • Shielding an enclosed space with the router still inside reflects RF inward and INCREASES your exposure

What I Actually Measured – TriField TF2 Readings at Palm Beach QLD

Before I tell you what to buy, here is what the numbers look like in a real Australian home. I took these readings with my TriField TF2 at home in Palm Beach QLD and photographed the meter display for every one. The router is a Telstra modem sitting next to the NBN connection box.

RF power density at close range to the router: 3.058 mW/m². The highest live reading I photographed there was 4.380 mW/m². Wi-Fi routers transmit in bursts, so the live number moves around; the TF2 also shows the peak. For context, ARPANSA’s RF exposure limit at 2.4 GHz is 10,000 mW/m² (10 W/m²), a thermal safety threshold designed to prevent tissue heating. My reading is 0.03% of that limit. You might think the conversation ends there.

It does not. The building biology guidelines for sleeping areas (SBM-2008) class RF above 0.01 mW/m² as a severe anomaly and above 1 mW/m² as extreme. That is precautionary, not regulatory. By that yardstick my close-range reading is extreme. So depending on which reference frame you adopt, the same reading is either negligible or significant. This is why you need your own data, not someone else’s opinion.

RF power density on the living room couch: 0.032 mW/m². At the bed, at pillow height, it was 0.048 mW/m². That is roughly 60 to 95 times lower than at the router, with no shielding and no special product: just distance and walls. By the building biology bands both are still in the severe range. A timer that cuts the router’s power removes the router’s share of that overnight.

I also measured the AC electric field at my timber bedhead: 50, 93 and 105 V/m on three passes, against 2 V/m on the pillow itself. That comes from the house wiring in the wall, not the router, and a router timer does nothing for it. Indoor RF-EMF exposure has broadly increased with the proliferation of home wireless devices – which makes your bedroom the most important room to measure.

Key takeaway: My TriField TF2 read 3.058 mW/m² at close range to the router and 0.032 mW/m² on the couch, about 95 times lower. A timer removes the router’s share while you sleep. Always measure before spending money.

The Dual Reference Problem – ARPANSA vs Building Biology

You will find two standards cited in every EMF discussion, and they are 10 million times apart. If you do not understand why, you will either dismiss the concern entirely or panic and overspend on shielding that might make your situation worse. Neither outcome is useful.

ARPANSA’s Radiation Protection Standard (RPS S-1), aligned with ICNIRP guidelines, sets the RF exposure limit at 2.4 GHz at 10 W/m² (10,000 mW/m²). This is a thermal safety limit. It protects against tissue heating – the same mechanism as a microwave oven. At 3.058 mW/m², my router reading is 0.03% of this limit. By ARPANSA’s framework, there is no safety concern. ARPANSA maintains regular RF-EMF exposure literature surveys through their research program, and their position is that compliance with ICNIRP limits provides adequate protection based on the weight of current evidence.

The building biology guidelines for sleeping areas (SBM-2008), published by the Institut für Baubiologie in Germany, treat RF above 0.0001 mW/m² as an anomaly and above 0.01 mW/m² as severe. This is a precautionary guideline based on non-thermal biological research – effects on melatonin production, cell membrane permeability, and sleep quality at exposure levels far below thermal thresholds. It is not a regulatory standard. No government anywhere enforces it.

Here is the honest position: I am not a scientist, I am a former Navy Clearance Diver who measures things for a living. I cannot tell you which standard is “correct” – that question will be argued by researchers for another decade. What I can tell you is that reducing a known RF source during the 8 hours you sleep costs $15 and has no downside. You do not need to resolve the scientific debate to act on the low-cost interventions. The timer does not care which reference frame is correct. It simply removes the signal.

What I refuse to do is frame ARPANSA’s limit as proof that routers are safe, or frame building biology guidelines as proof that they are dangerous. Both frames sell products. The readings sell nothing – they tell you what is actually happening in your house. That is why the TriField TF2 is the first purchase, not a shielding canopy.

Key takeaway: ARPANSA’s thermal limit (10,000 mW/m²) and the building biology ‘no anomaly’ level (0.0001 mW/m²) differ by a factor of 100 million. You do not need to pick a side to act: a $15 timer eliminates 100% of router RF during sleep regardless of which framework you follow.

Why a Mechanical Timer – Not a Smart Timer, Not an App

This is where most people get it wrong. They search for “Wi-Fi timer” and buy a smart plug that connects to their home Wi-Fi, which they then use to turn off… their Wi-Fi. Think about that for a moment. A TP-Link Kasa smart plug broadcasts its own 2.4 GHz signal and requires a cloud connection. You have replaced one RF source with another.

A mechanical timer has no wireless components. It is a spring-loaded dial with physical pins that interrupt mains power at the times you set. No Wi-Fi chip, no Bluetooth, no standby transmission. When the timer clicks off (mine at 9pm), the router loses power completely. Zero RF output. Zero standby draw. The HPM 24 Hour Analog Timer (Amazon AU ASIN B0G92V9FH3) is a typical option, rated for Australian 240V/10A mains – well within the power draw of any consumer router.

Here is why this matters more than you think. Your router broadcasts continuously, even when no device is actively using the internet. Wi-Fi access points send beacon frames every 100 milliseconds – that is 10 bursts per second, 24 hours a day, 365 days a year – whether anyone is streaming, browsing, or sleeping. The router does not know you are asleep. The beacon frames alone produce measurable RF at your bed head. A timer is the only intervention that eliminates this completely.

Some routers offer a “scheduled Wi-Fi off” feature in their admin settings. This can work, but with two caveats. First, it only disables the Wi-Fi radio – the router’s Ethernet ports and internal processor remain powered, and some routers still emit low-level RF from internal clocks and Bluetooth modules in standby. Second, firmware updates can reset scheduled settings. A mechanical timer is physical, redundant, and firmware-independent.

For homes in suburban Brisbane, Sydney, Perth, or Melbourne where NBN routers sit in hallways or living rooms adjacent to bedrooms, this single intervention changes the sleep environment more than any product costing 10 or 50 times as much. If your router is in the same room as your bed, which is common in apartments, the timer is not optional. It is the baseline.

Key takeaway: Never use a smart plug (Wi-Fi/Bluetooth) to control a router timer – it emits its own RF signal. A $15-$20 mechanical timer from Bunnings physically interrupts mains power with zero wireless output.

The Inverse Square Law – Why Distance Beats Shielding

RF power density decreases with the square of the distance from the source. Double the distance, and the power density drops to one quarter. Triple the distance, and it drops to one ninth. This is not a theory or a guideline – it is a law of physics that applies to every electromagnetic wave at every frequency.

My readings show the scale of it. At close range to the router the TriField TF2 read 3.058 mW/m². On the living room couch it read 0.032 mW/m², and at the bed 0.048 mW/m². Walls add to distance: plasterboard and framing absorb part of a 2.4 GHz signal, and foil-backed sarking absorbs more.

This is why I tell every person who asks me about EMF reduction to start by moving the router. If your router sits on your bedside table, moving it to a room 5 metres away cuts its signal at your pillow sharply: in open space the inverse square law predicts 25 times less at 5 metres than at 1 metre, before you spend a single dollar. Add the timer and the router’s share drops to zero while it is off.

Contrast this with shielding products. An EMF shielding bed canopy (silver cotton, 42 dB rated) costs $300 to $1,500 depending on size. It works by reflecting RF signals. But here is the critical fact that shielding vendors rarely emphasise: if the primary RF source is inside the shielded enclosure – or if a phone, tablet, or smart watch is inside the canopy with you – the canopy reflects the signal back and forth, creating standing waves that can INCREASE your exposure. A device left running inside a canopy can read higher than the same device in an open room.

The correct sequence, every time, in every Australian home:

  1. Measure with a TriField TF2 or Safe and Sound Pro II – identify your actual sources and levels
  2. Remove sources from the bedroom – phone on airplane mode, router on a timer, no smart speakers
  3. Increase distance – move the router to the room furthest from bedrooms
  4. Shield external residual only – if neighbours’ Wi-Fi or a nearby mobile tower still registers above your threshold after steps 1-3

Skipping to step 4 is the most expensive mistake in EMF reduction. Shielding paint and canopies do nothing about your own router, smart TV and phone, which are usually the dominant sources.

Key takeaway: My couch read 0.032 mW/m² against 3.058 mW/m² at the router: about 95 times lower, with no shielding. Moving the router and adding a timer is free or $15. Shielding costs $300-$1,500 and can backfire if internal sources remain. Distance first, shielding last.

Step-by-Step: How to Set Up Your Router Timer

This takes five minutes. No electrician required. No tools. Here is the exact process I use at my Palm Beach home.

Step 1: Buy a mechanical 24-hour timer. The HPM 24 Hour Analog Timer is a typical mechanical option. Available on Amazon AU (ASIN B0G92V9FH3) or from hardware stores for around $15-20. It is rated for Australian 240V mains at 10A – your router draws under 0.5A, so there is no risk of overload. Do not buy a digital timer with a Wi-Fi chip. Do not buy a smart plug. If it has an app, it has an antenna, and it defeats the purpose.

Step 2: Set your off-period. Push down the pins on the timer dial corresponding to the hours you want the router powered off. I set mine from 9pm to 6am: nine hours with the router off across the night. The timer has 96 pins in 15-minute increments, so you can set it precisely. If you work from home and start early, adjust to 10pm-5:30am. The point is that you get at least 7-8 hours of complete radio silence during sleep.

Step 3: Plug the timer into the power outlet. Plug your router’s power adapter into the timer. Plug the timer into the wall. Set the current time by rotating the dial to align the arrow with the current hour. Flip the switch on the side to “Timer” mode (not “On” which bypasses the timer).

Step 4: Verify with a meter. This is optional but worth doing once. After the timer clicks off, hold a TriField TF2 at 1 metre from the router. The router’s contribution should be gone. Whatever reading remains is coming from another device – a smart TV, a phone, a baby monitor, a mesh Wi-Fi extender. Identify and address each one.

Step 5: Address phones and tablets. A timer on the router does nothing if your phone is still transmitting Wi-Fi probe requests, Bluetooth scans, and cellular data from your nightstand. Put your phone on airplane mode before bed. This is free and takes two seconds. If you use your phone as an alarm, airplane mode preserves the alarm function – it still works. The combination of router timer plus phone airplane mode eliminates the two largest RF sources in virtually every Australian bedroom.

For households with NBN HFC or FTTP connections, note that the timer cuts power to both the router and, if you have a separate NBN connection box (NTD), the router only. The NTD should remain powered – cutting power to it can trigger reconnection delays of 5-15 minutes in the morning. Plug only the router into the timer; leave the NTD on a separate outlet.

Key takeaway: Five-minute setup: plug mechanical timer into wall, plug router into timer, set an overnight off-period (mine is 9pm to 6am), verify with a meter. Put your phone on airplane mode. Total cost: $15-$20 for the timer, $0 for airplane mode.
Free audit

Check all seven rooms, not just this one

38 checks, 29 free, ranked by impact. Sent as a 32-page PDF.

We'll email you the audit and a short series of practical guides. Unsubscribe in one click, any time. Privacy.

Sent. Taking you to your download...

The Full Bedroom Protocol – Router Timer Plus Three Other Fixes

The router timer handles RF from Wi-Fi. But your TriField TF2 measures three types of field: RF, AC magnetic, and AC electric. At my timber bedhead the AC electric field read 50 to 105 V/m, while the pillow surface read 2 V/m. That field comes from the 240V wiring in the wall, energised all night even with nothing plugged in, and a router timer does nothing for it.

Here are the four interventions I use, ranked by cost and impact:

Intervention Cost Field Type Effect
Phone airplane mode $0 RF Phone RF drops to 0 mW/m²
Mechanical timer on router ~$15-$20 RF Router RF drops to 0 mW/m²
Demand switch on bedroom circuit ~$100-$150 (electrician) AC electric Cuts the circuit’s AC electric field (my bedhead: 50 to 105 V/m)
EMF bed canopy (external sources only) $300-$1,500 RF Varies – only effective if no internal RF sources remain

The demand switch deserves specific attention. It is a device installed by a licensed electrician in your switchboard that detects when no current is being drawn on the bedroom circuit. When all lights are off and nothing is plugged in (or only a battery alarm clock), the demand switch drops the circuit voltage from 240V to a low DC test voltage. This eliminates the AC electric field radiating from every cable in your bedroom walls. Cost: approximately $100-$150 installed, depending on your electrician and switchboard layout. If your bedhead electric field is high, it is the targeted fix.

Notice the sequence: free and cheap fixes first, then a targeted fix for wiring, and shielding last. The building biology guidelines for sleeping areas (SBM-2008) put RF above 0.01 mW/m², AC magnetic above 1 mG and AC electric above 1.5 V/m in the severe range. Getting below those levels comes from following the correct sequence, not from a single product.

For readers in apartments – particularly in high-density areas like Sydney’s Surry Hills, Melbourne’s Southbank, or Brisbane’s South Brisbane – your neighbours’ Wi-Fi networks may contribute measurable RF even after your own router is off. This is where the complete guide to EMF in Australian homes covers shielding options for external sources. But measure first. A neighbour’s router through a concrete wall is usually far weaker than your own router at close range, but measure it rather than assume.

Key takeaway: The full bedroom protocol costs under $200: phone airplane mode ($0) + mechanical timer ($15-$20) + demand switch ($100-$150). This addresses RF, AC electric, and most AC magnetic fields. Shielding is step 4, not step 1.

What About the JRS Eco 100 Low-EMF Router?

If you want to reduce RF exposure during waking hours – when you actually need Wi-Fi – the next step after the timer is a low-EMF router. The JRS Eco 100 is the only consumer router I am aware of that reduces beacon frame transmission rate and implements a full-eco standby mode, cutting RF output by approximately 90% when no device is actively transferring data.

Standard routers broadcast beacon frames every 100 milliseconds regardless of traffic. The JRS Eco 100 extends this interval and drops to near-zero output during idle periods. The manufacturer states the JRS Eco 100 reduces idle RF output by approximately 90% compared with a standard always-on router, for comparison, my standard router read 3.058 mW/m² at close range.

At approximately $450 from SaferEMF AU, it is not cheap. But for households where someone works from home and needs daytime Wi-Fi – particularly if the home office is in a bedroom or small apartment – the combination of a JRS Eco 100 during the day plus a mechanical timer at night covers both scenarios. The timer is still the higher-ROI purchase. Buy the timer first, measure the difference, then decide if the JRS Eco 100 is worth the additional investment for your specific situation.

Common Mistakes That Waste Money or Increase Exposure

These are the mistakes I see most often in product claims and EMF advice. Each one costs money, time, or – in the worst case – actually increases RF exposure in the bedroom. Here are the five most common.

Mistake 1: Using a smart plug as a router timer. I have covered this above, but it bears repeating because it is the most common error. Any plug with “Wi-Fi”, “Bluetooth”, “smart”, or “app control” in the description is emitting RF. The TP-Link Tapo, Kasa, and similar smart plugs broadcast a 2.4 GHz signal continuously. You are replacing one RF source with another. Mechanical only.

Mistake 2: Shielding before removing internal sources. An EMF bed canopy works by reflecting RF. If your phone, router, or smart speaker is inside the canopy, the reflected signal bounces between you and the conductive fabric repeatedly. A canopy with an active phone inside can show higher RF power density than an open room. The correct sequence is always: remove sources → increase distance → then shield external residual only.

Mistake 3: Ignoring the smart meter. Australian smart meters operate at 900 MHz and transmit in bursts. The time-averaged output may be low, but peak readings can be 100-1,000× higher than the time-average. If your smart meter is mounted on the external wall of your bedroom – common in Queensland and Victorian homes – it may be the dominant RF source after you have dealt with the router and phones. A TriField TF2 will show you. If it is a problem, the solution is typically a shielding plate behind the meter (external, not internal) or relocating the bed to the opposite wall.

Mistake 4: Forgetting mesh extenders and IoT devices. Your main router is on a timer, but the mesh extender in the hallway is still broadcasting. The Ring doorbell is still pinging. The smart fridge is still connected. Every Wi-Fi-enabled device in your home is an RF source. Walk through with the TriField TF2 after the router timer clicks off and identify every remaining signal.

Mistake 5: Not measuring before or after. Without baseline readings, you are guessing. Without post-intervention readings, you do not know if your changes worked. The TriField TF2 (Amazon AU, ASIN B078T2R64C) measures all three field types – RF, AC magnetic, and AC electric – in one device. It costs about $250 to $270 in Australia, and it turns every decision from opinion into measurement. If that is too much, the Safe and Sound Pro II from SaferEMF AU is an RF-only meter with excellent sensitivity and an audio readout that makes scanning a room fast and intuitive.

Key takeaway: The five most common EMF reduction mistakes all stem from the same error: acting before measuring. A smart plug replaces one RF source with another. A canopy over an active phone amplifies the signal. Measure → remove → distance → shield. In that order, every time.

Decision Tree: Your EMF Reduction Sequence

Use this three-question framework to determine your next step. It applies to every Australian home regardless of construction type, location, or budget.

Question 1: Do you have a meter?

  • No → Your first purchase is a TriField TF2 (~$400) or, if budget is tight, a Safe and Sound Pro II (~$550 from SaferEMF AU) for RF-only. Without readings, every decision is a guess.
  • Yes → Move to Question 2.

Question 2: Is your router the dominant RF source at your bed head?

  • Yes → Buy a HPM 24 Hour Analog Timer ($15-$20). Move the router to the furthest room from bedrooms. Put phones on airplane mode. Re-measure.
  • No → Identify the dominant source (smart meter, neighbour’s Wi-Fi, mesh extender, phone). Address that source first.

Question 3: After removing internal sources and increasing distance, is your bed head RF still above your target threshold?

  • Yes → Now consider shielding for external sources. A shielding bed canopy or shielding paint on the wall facing the external source is appropriate.
  • No → You are done. Re-measure quarterly or after any new device is added to the home.

This sequence prevents the most expensive mistake: spending $800 on shielding when a $15 timer and airplane mode would have solved 90% of the problem. Start cheap, measure the result, and only escalate spending when the numbers justify it.

Key takeaway: Three questions determine your entire EMF reduction plan: (1) Do you have a meter? (2) Is the router the dominant source? (3) After removing internal sources, do you still have elevated readings? Most people never need to get past question 2.

Final Verdict

A $15 mechanical timer on your router is the single highest-return EMF intervention available to any Australian household. It eliminates 100% of your router’s RF output during sleep. Combined with phone airplane mode (free) and distance (free), you address the two largest RF sources in most homes for under $20 total.

My TriField TF2 readings at Palm Beach QLD show the scale: 3.058 mW/m² at close range to the router and 0.032 mW/m² on the couch. With the router off there is no router signal at all. You do not need to resolve the debate between ARPANSA’s 10,000 mW/m² thermal limit and the building biology bands to justify this intervention. It costs $15, takes 5 minutes, has no downside, and works regardless of which framework you adopt.

If you want to verify your own numbers – and you should – the TriField TF2 is the meter I use and recommend. It measures RF, AC magnetic, and AC electric fields in one device, which means you will also discover whether your bedroom wiring needs a demand switch (my bedhead read up to 105 V/m).

Measure first. Remove sources second. Increase distance third. Shield last. That is the sequence. Everything else is marketing.

Last reviewed: July 2026 – Clean and Native

Start with measurement. The TriField TF2 is the only meter you need.

Measures AC magnetic, AC electric, and RF in one device. Without real readings, every EMF decision is a guess.

Frequently Asked Questions

Does turning off my router at night with a timer actually reduce EMF?

Yes. A router that has no power produces zero RF output. Mine is on a timer from 9pm to 6am; when it is on, my TriField TF2 reads 3.058 mW/m² at close range.

Will a smart plug work as a router timer for EMF reduction?

No. Smart plugs broadcast their own 2.4 GHz Wi-Fi or Bluetooth signal continuously, replacing one RF source with another. Use a mechanical timer with no wireless components, such as the HPM 24 Hour Analog Timer.

How far should my router be from my bedroom?

As far as practical. The inverse square law means doubling distance cuts RF power density to one quarter. At my Palm Beach home the reading dropped from 3.058 mW/m² at close range to 0.032 mW/m² on the living room couch, about 95 times lower.

What is ARPANSA’s RF exposure limit for Wi-Fi routers in Australia?

ARPANSA’s Radiation Protection Standard (RPS 3), aligned with ICNIRP, sets the RF limit at 2.4 GHz at 10 W/m² (10,000 mW/m²). This is a thermal safety limit designed to prevent tissue heating, not a precautionary guideline for long-term low-level exposure.

What does building biology recommend for RF in sleeping areas?

The building biology guidelines for sleeping areas (SBM-2008) class RF above 0.01 mW/m², AC magnetic above 1 mG and AC electric above 1.5 V/m as severe anomalies. These are precautionary guidelines, not regulatory limits.

Can an EMF shielding canopy make my exposure worse?

Yes. If any RF source – phone, tablet, smart watch, or router – is inside the canopy, the conductive fabric reflects the signal inward, which can increase exposure. Always remove all internal RF sources before using any shielding enclosure.

What is a demand switch and do I need one?

A demand switch is installed by a licensed electrician in your switchboard. It cuts the 240V AC voltage on your bedroom circuit when no current is being drawn, eliminating the AC electric field from wiring in your walls during sleep. Cost is approximately $100-$150 installed. It is worth considering if a TriField TF2 shows a high AC electric field at your bedhead, as mine did at 50 to 105 V/m.

Will turning off my router at night affect my NBN connection?

Put only the router on the timer, not the NBN NTD (connection box). The NTD maintains your line sync. When the router powers back on in the morning, it reconnects within 30-90 seconds. Some routers take up to 2-3 minutes on HFC connections. There is no long-term impact on your NBN service.

Does the TriField TF2 measure Wi-Fi router emissions accurately?

The TriField TF2 measures RF from 20 MHz to 6 GHz, which covers both 2.4 GHz and 5 GHz Wi-Fi bands. It captures peak readings from burst transmissions, which is appropriate for Wi-Fi signals that pulse rather than transmit continuously. For dedicated RF measurement with higher sensitivity, the Safe and Sound Pro II is the specialist alternative.

How much does the full bedroom EMF reduction protocol cost?

Under $200 for most Australian homes: phone airplane mode ($0) + Jackson mechanical timer (~$15-$20) + demand switch on bedroom circuit (~$100-$150 installed by a licensed electrician). This addresses RF, AC electric, and most AC magnetic fields without any shielding products.

Jayce Love, former Royal Australian Navy Clearance Diver and Clean and Native founder
Written by Jayce Love

Former Royal Australian Navy Clearance Diver and TAG-E counter-terrorism operator. Founded Clean and Native to apply the same rigorous thinking to the home environment.

Full biography →
Free · 32-page PDF

The 7-Room Home Audit

Distance and off-time do most of the work, and they are free. The audit maps every room: 38 checks across EMF, air and water, ranked by impact.

  • Our own TF2 readings from router to pillow
  • What to check behind the bedhead wall
  • ARPANSA limits and precautionary bands, side by side

We'll email you the audit and a short series of practical guides. Unsubscribe in one click, any time. Privacy.

Sent. Taking you to your download...

Similar Posts